Electricians
Recessed Lighting Installation Cost Per Light (2026)
Planning a recessed lighting installation job? Get your own price range free.
Snap 1–3 photos and get a price range for your job in about 30 seconds, then get matched with a local pro if you want a real quote. No signup. →
Recessed lighting installation typically costs $150 to $400 per light in 2026, including the fixture and labor. A typical room with 6 recessed lights runs about $900 to $2,400. Ultra-thin LED wafer lights in an existing ceiling are on the lower end; remodel cans in plaster ceilings, sloped ceilings, or ceilings with no attic access are on the higher end.
Recessed Lighting Cost Breakdown
| Scenario | Cost per light | Notes |
|---|---|---|
| New construction (open framing) | $100–$250 | Easiest access |
| LED wafer/canless retrofit | $125–$300 | Thin fixtures, smaller holes |
| Remodel cans, attic access | $150–$350 | Wire run through attic |
| Remodel cans, no attic access | $200–$400+ | Fishing between joists, more patching |
| Replace existing can with LED | $75–$175 | Trim or retrofit kit swap |
What Drives the Cost
- Ceiling access. First-floor ceilings under a finished second floor are harder than top-floor ceilings with attic access.
- Ceiling material. Plaster and lath takes longer and creates more patching than drywall.
- Number of lights. Per-light cost drops as the count rises because setup, the switch run and circuit work are shared.
- New circuit or switch. Adding a new switch leg or circuit adds $150 to $400.
- Dimmers and smart switches. $50 to $200 each installed.
- Insulation contact. Lights in insulated ceilings must be IC-rated.
- Drywall patching and paint. Often excluded — clarify in the quote.
How Many Recessed Lights Do You Need?
A common rule of thumb is to space lights roughly half the ceiling height apart — about 4 feet apart for an 8-foot ceiling — and 2 to 3 feet from walls. A 12x12 room often uses four to six lights.
Line Items on a Recessed Lighting Estimate
- Fixtures (housings and trims, or canless wafers)
- Wire and connectors
- Switch, dimmer or smart control
- Labor per light plus circuit work
- Drywall patching (if included)
- Permit (if required)
Quoting Tips for Electricians
Price recessed lighting as a base per-light rate plus adders: no-attic-access adder, plaster adder, new switch leg, and dimmer upgrade. That keeps quotes consistent and makes upsells easy to show. Customers can photograph the ceiling, attic access (if any) and the switch location, which covers most variables before a site visit.
Frequently Asked Questions
How much does it cost to install 6 recessed lights?
Usually $900 to $2,400, depending on ceiling access, fixture type and whether a new switch or circuit is needed.
Are LED wafer lights cheaper to install than cans?
Often, yes. Wafer lights need smaller openings and no separate housing, which saves labor in retrofits.
Do recessed lights need a new circuit?
Not always. Several LED fixtures draw little power and can often share an existing lighting circuit, but an electrician should confirm the load.
How long does recessed lighting installation take?
A room of four to eight lights typically takes half a day to a full day.
Estimate this job faster
Electricians: get photo-based recessed lighting estimates drafted from your own per-light rates and adders. Try Fast Snap Pro free for 7 days. Start your free trial.
Get a free price range for your recessed lighting installation job
Upload photos of your project. You'll see a price range with labor and materials broken out, and you can ask to be matched with up to 3 local pros.
Photos of the job (up to 3)
No signup. Photos are sent to the AI only for this estimate and aren't saved.
Are you a contractor?
Send a link, get photos back with a priced estimate — using your own rates, not a generic price book.
Try Fast Snap Pro freeGuides for electricians
- Electrician Price List: Building Flat Rates for Common Electrical Jobs
- Electrical Estimating Software (2026): Takeoff Tools vs Photo-Based Quoting
- How to Estimate Electrical Jobs: A Practical Pricing Guide
- Photo-to-estimate app for contractors